If you are worried about losing your data after a full wipe, why not use the LG Bridge software to backup and restore. Make sure you select REFURBISH this will do a full wipe, tick BIN file. TO GO BACK TO LP FROM MM - Open LGUP on your computer, click on FILE PATH and point it towards your LP KDZ. Select REFURBISH and make sure BIN file is ticked. Now open LGUP again - you will notice that the MM KDZ will still be showing in the FILE PATH section. TO DO A FULL WIPE AND INSTALL MM - Open the LGUP on your computer. MAKE SURE YOU HAVE CLICKED UPGRADE! This will update you from LP to MM with out wiping any of your info. TO UPGRADE TO MM from LP - make sure BIN file is ticked and in the File Path point it towards the MM KDZ you have downloaded. If you have a problem that LGUP does not see your LG G4, leave your mobile connected via USB and leave LGUP running, restart your mobile, hopefully this will solve the problem. Start LGUP prog on your computer "make sure your phone is plugged in" Make sure you have downloaded the required KDZ file MM or LP LGUP WILL FLASH YOUR KDZ filesĭownload LGUP fromor here thank you hyelton for this link :good: My Links are ALWAYS hosted on MY servers for NO Downtime! If My site does NOT have what your looking for PM me or post what you want and I will try and get it for youįeel Free to support me by helping with Server Costs and Coffee if you feel my work has helped you Thank you! REMEMBER if you get Bootlooping after flashing perform a factory hard reset! Make sure your using a USB 2.0 port, USB 3.0 will not work (only works for 1% of users) To Fix ANY Driver issues make sure you reboot your computer after removing and then re-install again, Also try different USB ports or USB cable or try another PC. Remember if you have bootloop or stuck on LG Logo after flashing make sure you FACTORY RESET! When all is done, reboot your phone and enjoy!Ĭredit for making a cleaner guide for the TOT Method Your LG G2 will restart showing firmware installation progress in percent (%). Ignore if you see any temporary error and just wait patiently till it is finished.ġ4) Press and hold power button until phone turns off, leaving usb cable connected to device AND computer ,immediately hold volume up button until phone boots it into Download Mode. The firmware installation will be triggered. tot extension.(the 2.04 gb file from above)ġ3) Now click the Yellow arrow button on the top left of the main window. You might see a window with Korean language, just click on OK.ġ0) MAKE SURE UNDER, DEVICE MANAGER, YOUR PORT IS SET TO COM 41 FOR YOUR DEVICE.ġ1) Click the DLL box and choose the dll file from above for you phone model.ġ2) Click the S/W box and select the firmware file with. To do this, press and hold the Volume Up key and then plug the USB cable. Replace the old MegaLock.dll file if you have already installed LG Flash Tool on your computer.Ĩ) When the firmware is downloaded, boot your LG G2 into Download Mode. When LG Flash Tool is installed, do not launch it.ħ) Copy MegaLock.dll to C:\LG\LGFlashTool, This is a hidden folder so enable "hidden folders". Install LGFlashTools v1.8 (but don't run it) Install the LG drivers downloaded above.Ģ. Or, you may remove the MicroSD card, then power on the phone.1. Hold Volume – AND Power, a message will show up confirming the factory reset. In this case follow the Hard Reset Procedure below. Once done you can detatch the USB cable and see if the phone boots up. Yes I select it because I am in Canada.Īfter this the LG flashing tool should start analyzing your phone and flashing the. – Select different country if you’re not in Korea. – Click “Clear phone Software update Registry” Wait a few seconds an a new window will pop up. In the next window click “Upgrade Start”Ħ. Once done, click “Normal web upgrade test”ĥ. Now run as administrator UpTestEX.exe and do the following: Go to the bar at the bottom right, and click once with the left mouse button over the icon of WindowsEnabler, so that appears the “On”message.Ĥ. Go back to Flashtool folder and run as administrator WindowsEnabler.exe. Turn off the phone and connect it to the PC with the USB cable. Extract the “Flashtool” folder on the desktop, or where you want. Use Premium download, if you want to download them faster.ġ. Download and install LG Mobile Support Tool Ĥ. Google and install the LG USB drivers if you don’t have it.ģ. I DO NOT TAKE ANY RESPONSIBILITY IF YOU BRICK YOUR PHONE. You may use it as a reference, not a guide. Here is a record of how I flash my LG P500h android phone to the original Telus ROM.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |